A dryer that tumbles without heat leaves clothes damp after a full cycle, and a dryer that will not start at all leaves a wet load sitting in the drum. Both faults have the same set of usual causes, and sorting them out is a matter of testing one part at a time. The heating element or gas burner makes the heat, the thermostat and thermal fuse control it, the belt and motor turn the drum, and the vent carries the hot, damp air out of the house. When any one of those stops working, the rest of the machine cannot do its job.
Massachusetts homes run dryers hard through the winter, when thick clothes and bedding need long cycles and the air coming into the house is cold and dry. Lint builds up in the vent over time, and a vent that is partly blocked makes the dryer work longer, run hotter, and wear out its heating parts faster. A burning smell from a dryer is never a small thing: it usually means lint has collected near the heater or the belt is slipping and heating up against the drum.
This page explains the most common dryer faults, including the dryer that will not heat, the drum that will not turn, and the machine that stops partway through a cycle.
Dryer Not Heating
A dryer that tumbles but does not heat has a fault in the heating circuit, and the first part to test is usually the thermal fuse. The fuse is a safety device: it breaks the circuit when the dryer overheats, which is exactly what happens when the vent is blocked and hot air cannot escape. A blown fuse is a symptom as much as a fault, so a technician who replaces the fuse without checking the vent will be back when the new fuse blows again.
On a gas dryer, the heat comes from a burner rather than an element, and the parts are different: the igniter that lights the gas, the gas valve coils that open the valve, and the flame sensor that confirms the flame is lit. An igniter that glows without lighting the burner points at the coils; a burner that lights and then goes out points at the flame sensor or the gas supply.
Dryer Will Not Start or Will Not Spin
A dryer that will not start at all usually has a door switch that no longer registers the door as closed, a broken belt that has tripped the belt switch, or a blown thermal fuse that has cut power to the whole machine. The door switch is tested first, because it is the part that moves every time the dryer is used and the part that wears out soonest.
When the drum will not spin, the belt is the usual suspect. Belts stretch, fray, and snap, and a belt that has slipped off its pulley will leave the motor spinning freely while the drum sits still. The drum rollers and the idler pulley carry the drum and keep the belt tight; when their bearings wear out, the drum drags, squeals, and eventually stops turning. The technician opens the cabinet, checks the belt and rollers by hand, and tests the motor.
Electric Dryer and Gas Dryer Differences
Electric and gas dryers look the same from the front, but their heating systems are entirely different, and the diagnosis follows different paths. An electric dryer heats with a coiled element powered by a 240-volt supply, and a fault can sit in the element, the thermal fuse, the high-limit thermostat, or the supply itself, including a breaker that has tripped on one leg so the drum still turns but the heat never comes on.
A gas dryer heats with a burner fed by a gas line, and its faults are the igniter, the gas valve coils, the flame sensor, and the gas supply. A gas dryer that runs but does not heat may have an igniter that has cracked, which is a common failure and a straightforward replacement. Both types share the same drum, belt, motor, rollers, and vent, so a spin fault or a noise fault is diagnosed the same way on either type.
Dryer Vent and Lint Cleaning
The vent is the part of a dryer that most people never see, and it causes more dryer trouble than any single part inside the machine. Lint escapes the lint filter on every load and collects in the vent hose and the duct that runs through the wall or the floor. As the layer thickens, air moves more slowly, clothes take longer to dry, the dryer runs hotter, and the thermal fuse is more likely to blow.
Cleaning the vent means disconnecting the hose, clearing the duct with a brush or compressed air, and checking that the outside vent flap opens freely and is not blocked by a nest or debris. A short, straight run of rigid metal duct dries clothes fastest and collects the least lint; a long run with several bends needs cleaning more often. The lint filter itself should be cleared after every load, and a filter that has a waxy coating from dryer sheets should be washed, because a coated filter blocks airflow just as surely as a blocked vent.
Frequently asked questions
Why is my dryer not heating?
A blown thermal fuse, a broken heating element, a faulty thermostat, or a blocked vent are the usual causes on an electric dryer. On a gas dryer, the igniter or the gas valve coils are the likely faults.
Why does my dryer take so long to dry clothes?
A partly blocked vent is the most common cause. Lint in the duct slows the airflow, so the dryer needs more time and runs hotter to finish a load.
What causes a burning smell from a dryer?
Lint collected near the heater or a slipping belt are the usual causes. Stop the dryer, clean the lint filter, and have the vent and belt checked before using it again.
Why will my dryer not start?
A worn door switch, a broken belt, or a blown thermal fuse are the usual causes. The door switch is tested first because it wears out soonest.
Why is my dryer so noisy?
Worn drum rollers, a worn idler pulley, or a belt that is slipping all make noise. A thumping sound often means a roller has flattened; a squeal usually means a belt or pulley bearing.
Is a gas dryer different to repair than an electric dryer?
The heating parts are different: gas dryers use an igniter, gas valve coils, and a flame sensor, while electric dryers use a heating element and thermostats. The drum, belt, motor, and vent are the same on both.
Call now โ describe the problem
An independent local provider looks at the machine, tests it, and tells you the fault and the fix in plain words.